BERKELEY SENSOR & ACTUATOR CENTER
UC BERKELEY UC DAVIS
User: Guest |  Site Map |  My BSAC Profile
HOME  PROJECTS  THRUSTS  PUBLICATIONS  ABOUT BSAC  DIRECTORY  ALUMNI  FOR BSAC RESEARCHERS  EVENTS CALENDAR  SECURE LOGIN
Howe
     
 Lee
 Lin
 Wu
 Howe
 Tien
 

APP62: Piezoelectric Aluminum Nitride Vibrating RF MEMS for Radio Front-End

Project ID APP62
Website
Start Date Fri 2003-Feb-07 15:08:19
Last Updated Wed 2005-Aug-24 08:18:22
Abstract The demand of consumer electronics for RF filters and frequency reference elements has focused attention on the reduction of size, power consumption and price and pushed current research interests towards the manufacturing of a single-chip, integrated RF solution. Vibrating contour-mode MEMS resonators constitute the most promising technology for ultimately realizing this vision. This project deals with analytical and experimental results on a new class of contour-mode aluminum nitride piezoelectric resonators. The realization of contour mode shapes in piezoelectric resonators, differently from commercially available FBAR resonators for which the thickness sets the resonant frequency, permits the definition of multiple frequencies on the same silicon substrate in a very economical manner by using one simple lithographic step. Multi-frequency and multi-band single-chip resonant platforms can be fabricated using this new class of resonators. The use of piezoelectric transduction also has a definitive advantage over electrostatically-driven contour-mode resonators by solving the problem of large motional resistance. Piezoelectric body forces intrinsically offer higher electromechanical coupling coefficients than corresponding surface-based electrostatic forces, making possible low values of motional resistance and the direct interface of these devices with 50 systems. Experimental results on different contour-mode structures have demonstrated that rectangular plates and circular rings constitute the most promising topologies for the realization of next-generation multi-frequency resonant platforms. Rectangular plate resonators have shown, for example, quality factor, Q, of 2,100 in air and motional resistance of 125 at a frequency of 85 MHz. At the same time circular ring resonators were fabricated on the same substrate demonstrating Q of 2,900 in air at 473 MHz and a motional resistance of approximately 84 . The highest Q of 4,300 was reported for a ring resonator at 230 MHz in air. In order to offer an understanding of Q dependence on anchor losses, extensive experimental studies were conducted for the rectangular plates and circular rings by changing the dimensions of the suspending tethers. In general, the smaller the number of tethers and the size of the tethers are, the lower the effect on Q degradation is. The width of the support does not seem to affect the Q of the ring resonator. To further prove the commercial viability of such technology, ladder filters were realized out of arrays of contour-mode resonators. Intermediate frequency (IF) filters at 93 and 236 MHz were fabricated using rectangular plates and circular rings, respectively. These filters show very promising performance, being characterized by low insertion losses (4 dB at 93 MHz), large close-in and out-of-band rejection (approximately 40 dB and above 27 dB, respectively, for a 93 MHz filter) and fairly sharp roll-off with a 20 dB shape factor of 2.2. The filters realized within this project are about 20X smaller than existing SAW technology, commonly used in the IF bands for cell phones. In addition, with a temperature coefficient of - 25 ppm/C, they have 40 % lower temperature sensitivity than SAW filters. Given the relatively small value of the motional resistance of the individual resonators, these piezoelectric contour-mode filters can be interfaced to 50 systems by on-chip components. Another important feature of these devices is the ability to lithographically define the mass loading mechanism needed to get the few percent frequency shift used in ladder filters. This feature is unique of contour-mode technology and is another economical advantage in the overall manufacturing process. In order to solve capacitive feed through problems experienced in high frequency resonators, a new class of two-port stacked resonators is introduced. Similarly to macroscale resonant transformers, for the first time, a two-port vertical topology was successfully implemented in piezoelectric aluminum nitride micromachined rectangular plates. These rectangular plate resonators have shown Q of 1,700 with a motional resistance of 175 at 83 MHz and a feed through capacitance of only 20 fF. This topology maintains large electromechanical coupling, eliminates spurious responses and especially reduces feed through capacitance offering the potential for higher frequencies of operation.
Status Completed
Funding Source Federal
IAB Research Area Wireless, RF & Smart Dust
Researcher(s) Gianluca Piazza
Advisor(s) Albert P. Pisano
Detailed Information
Secure Access

Private Abstract
Research Report
Poster Slide
Summary Slide PDF | VIDEO
Active Feedback (or Request for Response)

 

  • Copyright Notification: All papers downloaded from this site are © University of California or the publisher, all rights reserved. Contact the BSAC Webmaster for permission related to copyrighted materials.
  • Links on these pages to commercial sites do not represent endorsements by UC or its affiliates.
  • Privacy Policy
  • Contact Us

   webmaster@bsac.eecs.berkeley.edu
  User logged in as: Guest
  User Idle since: December 19, 2014, 2:47 pm